NoLo X-Loader (v0.9.14, Nov 29 2006) OMAP NAND Controller rev. 1.1 Flash id: 1580a1ec Secondary image size 87000 Booting secondary TAHVO v5.2 found USB transceiver powered up Retu v3.0 found VAux voltage set to 2.8V MicB2 output pulled down in power down mode Nokia OMAP Loader v0.9.14 (Nov 29 2006) running on Nokia 770 F5 OMAP1710 detected, running at 252 MHz (12.0 MHz ref clock) ARM_PER 63 MHz OMAP DMA hardware version 1 Reset reason: sw_rst OMAP NAND Controller rev. 1.1 Flash id: 1580a1ec Detected 128 MB NAND Flash (page size 2048 bytes) Partition table successfully read Initializing LCD SoSSI rev. 1.21 initialized Detecting LCD panel lph8923 Panel ID: 009200 not detected ERROR: No LCD panel detected Tornado rev. 81 initialized (CNF pins 3) Loading kernel image info... done. Loading kernel (1239 kB)... done in 157 ms (7859 kB/s) Total bootup time 250 ms Booting. Uncompressing Linux...................................................................................... done, booting the kernel. Linux version 2.6.16.27-omap1 (bifh1@doree) (gcc version 3.4.2 (release) (CodeSourcery ARM Q3D 2004)) #1 PREEMPT Wed Nov 29 16:29:50 EET 2006 CPU: ARM926EJ-Sid(wb) [41069263] revision 3 (ARMv5TEJ) Machine: Nokia 770 Memory policy: ECC disabled, Data cache writeback OMAP1710 revision 8 handled as 16xx id: 8b5f702f03330200 SRAM: Mapped pa 0x20000000 to va 0xd0000000 size: 0x4000 CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists Kernel command line: root=1f03 rootfstype=jffs2 time [ 390.319641] Clocks: ARM_SYSST: 0x1000 DPLL_CTL: 0x2a93 ARM_CKCTL: 0x050e [ 390.319732] Clocking rate (xtal/DPLL1/MPU): 12.0/252.0/252.0 MHz [ 390.319793] Total of 128 interrupts in 4 interrupt banks [ 390.320037] PID hash table entries: 512 (order: 9, 8192 bytes) [ 390.320526] Console: colour dummy device 80x30 [ 390.320861] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 390.321899] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 390.327697] Memory: 64MB = 64MB total [ 390.327789] Memory: 62080KB available (2196K code, 430K data, 92K init) [ 390.469207] Security Framework v1.0.0 initialized [ 390.469451] Mount-cache hash table entries: 512 [ 390.470520] CPU: Testing write buffer coherency: ok [ 390.474731] NET: Registered protocol family 16 [ 390.475555] OMAP GPIO hardware version 1.1 [ 390.475769] LCD configuration missing, using default touchscreen configuration [ 390.479248] OMAP DMA hardware version 1 [ 390.479309] DMA capabilities: 000c0000:00000000:01ff:003f:007f [ 390.479797] Initializing OMAP McBSP system [ 390.479980] omap_dsp_init() done [ 390.480407] USB: hmc 16, usb2 alt 0 wires, Mini-AB on usb0 [ 390.484649] OMAP STI support loaded (HW v1.1) [ 390.487457] i2c_omap i2c_omap.1: bus 0 rev3.1 at 100 kHz [ 390.488159] Tahvo/Betty driver initialising [ 390.489196] Tahvo v5.2 found [ 390.489715] Retu/Vilma driver initialising [ 390.490722] Retu v3.2 found [ 390.491271] Tahvo USB transceiver driver initializing [ 390.492279] tahvo: Registering interrupt 0 for device vbus_interrupt [ 390.492706] USB cable disconnected [ 390.496032] usbcore: registered new driver usbfs [ 390.496582] usbcore: registered new driver hub [ 390.497436] Bluetooth: Core ver 2.8 [ 390.497497] NET: Registered protocol family 31 [ 390.497528] Bluetooth: HCI device and connection manager initialized [ 390.497619] Bluetooth: HCI socket layer initialized [ 390.501678] Power Management for TI OMAP. [ 390.501770] NetWinder Floating Point Emulator V0.97 (double precision) [ 390.501861] OMAP OCPI interconnect driver loaded [ 390.504364] OMAP DSP driver initialization [ 390.520385] JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2003 Red Hat, Inc. [ 390.521820] lowmem: Module initialized. [ 390.521911] io scheduler noop registered [ 390.522216] io scheduler cfq registered (default) [ 390.523376] lcd_mipid spi2.3: invalid display ID [ 390.552825] OMAP Watchdog Timer: initial timeout 60 sec [ 390.553527] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 390.572937] serial8250.0: ttyS0 at MMIO 0xfffb0000 (irq = 46) is a ST16654 [ 390.871002] loop: loaded (max 8 devices) [ 390.875762] PPP generic driver version 2.4.2 [ 390.880645] PPP Deflate Compression module registered [ 390.885864] PPP BSD Compression module registered [ 390.890625] tun: Universal TUN/TAP device driver, 1.6 [ 390.895904] tun: (C) 1999-2004 Max Krasnyansky [ 390.904846] Clock enabled to MCBSP1 & 3 [ 390.908935] TLV320AIC23 I2C version 1.9d (13-Jun-2006) [ 390.914154] Retu power button driver initialized [ 390.918884] retu: Registering interrupt 0 for device PwrOnX [ 390.925292] input: retu-pwrbutton as /class/input/input0 [ 390.931762] retu: Registering interrupt 2 for device RTCS [ 390.937347] retu: Registering interrupt 5 for device RTCA [ 390.944122] Retu watchdog driver initialized [ 390.948516] Retu/Vilma headset driver initializing [ 390.954254] omap-hw-nand: OMAP NAND Controller rev. 1.1 [ 390.959625] NAND device: Manufacturer ID: 0xec, Chip ID: 0xa1 (Samsung NAND 128MiB 1,8V 8-bit) [ 390.968475] omap-hw-nand: using PSC values 2, 2, 3 [ 390.973388] Scanning device for bad blocks [ 390.977630] Bad eraseblock 0 at 0x00000000 [ 391.017700] 5 cmdlinepart partitions found on MTD device omap-nand [ 391.023986] Creating 5 MTD partitions on "omap-nand": [ 391.029144] 0x00000000-0x00020000 : "bootloader" [ 391.035339] 0x00020000-0x00080000 : "config" [ 391.041137] 0x00080000-0x00280000 : "kernel" [ 391.046813] 0x00280000-0x00480000 : "initfs" [ 391.052642] 0x00480000-0x08000000 : "root" [ 391.058166] udc: OMAP UDC driver, version: 4 October 2004 [ 391.064361] udc: OMAP UDC rev 6.1, Mini-AB [ 391.068542] udc: hmc mode 16, tahvo-usb transceiver [ 391.073608] udc: fifo mode 0, 1832 bytes not used [ 391.079071] mice: PS/2 mouse device common for all mice [ 391.084899] OMAP Keypad Driver [ 391.089172] input: omap-keypad as /class/input/input1 [ 391.095520] ads7846 spi2.0: touchscreen, irq 175 [ 391.101470] input: ADS784x Touchscreen as /class/input/input2 [ 391.111602] Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC). [ 391.122253] ALSA device list: [ 391.125427] No soundcards found. [ 391.128906] Netfilter messages via NETLINK v0.30. [ 391.134216] NET: Registered protocol family 2 [ 391.211547] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 391.219787] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 391.227233] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 391.233978] TCP: Hash tables configured (established 4096 bind 4096) [ 391.240447] TCP reno registered [ 391.243804] ip_tables: (C) 2000-2006 Netfilter Core Team [ 391.253112] mmci-omap mmci-omap.2: cover is now closed [ 391.320404] TCP bic registered [ 391.323669] NET: Registered protocol family 1 [ 391.328125] NET: Registered protocol family 17 [ 391.332702] Bluetooth: L2CAP ver 2.8 [ 391.336364] Bluetooth: L2CAP socket layer initialized [ 391.341583] Bluetooth: RFCOMM socket layer initialized [ 391.346893] Bluetooth: RFCOMM TTY layer initialized [ 391.351867] Bluetooth: RFCOMM ver 1.7 [ 391.355590] Bluetooth: HIDP (Human Interface Emulation) ver 1.1 [ 391.361633] Disabling unused clock "bclk"... done [ 391.366516] Disabling unused clock "uart3_ck"... done [ 391.371765] FIXME: Clock "tc2_ck" seems unused [ 391.376312] Skipping reset check for DSP domain clock "dsptim_ck" [ 391.382476] Skipping reset check for DSP domain clock "dspxor_ck" [ 391.388702] Skipping reset check for DSP domain clock "dspper_ck" [ 391.395690] Bootup reason: sw_rst [ 391.399169] OMAP GPIO switch handler initializing [ 391.407409] headphone (GPIO 14) is now disconnected [ 391.412384] speaker (GPIO 58) is now disconnected [ 391.417236] prot_shell (GPIO 5) is now open [ 391.421508] bat_cover (GPIO 12) is now open [ 391.425964] OMAP Random Number Generator ver. 40 [ 391.431121] 128 words of entropy generated [ 391.663299] Empty flash at 0x001cf0c8 ends at 0x001cf800 [ 391.689514] VFS: Mounted root (jffs2 filesystem). [ 391.694641] Freeing init memory: 92K Enabling core dumps to /media/mmc1/core-dumps/...done. Starting DSME... done. Wait for DSME socket to appear dsme: reading bootreason from /proc/bootreason dsme: bootreason was other than mbus, let's wait for the battery type received state:9 dsme: battery type: 4 [ 393.089996] tahvo: Registering interrupt 7 for device [ 393.095977] retu: Registering interrupt 8 for device [ 393.104217] retu: Registering interrupt 1 for device [ 393.109771] tahvo: Registering interrupt 1 for device received state:2 R&D mode enabled Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting Unable to open frame buffer device /dev/fb0 Unable to initialize. Exiting [ 393.471984] Selected PERIPHERAL mode: no gadget driver, powering off. Entering state 'USER'. Unable to open frame buffer device /dev/fb0 Press any key for interactive startup Loading WLAN module... [ 394.873931] umac: module license 'Proprietary' taints kernel. [ 395.099700] CX3110x chip variant: STLC4370 [ 395.223846] CX3110x: firmware version: 2.13.0.0.a.13.14 [ 395.229339] Loaded CX3110x driver, version 0.8 Pushing the WLAN tuned values Pushing default country...[OK] Pushing MAC address...[OK] Pushing IQ tuned values...[OK] Pushing TX tuned values...[OK] Pushing TX limits...[OK] Pushing RX tuned values...Using default values [OK] Booting from Flash Mounting root on /dev/mtdblock4 [ 397.112854] jffs2_scan_dirent_node(): Node CRC failed on node at 0x06a627ec: Read 0xffffffff, calculated 0x707923ac [ 397.123565] Empty flash at 0x06a62824 ends at 0x06a63000 [ 397.231384] jffs2_scan_inode_node(): CRC failed on node at 0x0707a7d0: Read 0xffffffff, calculated 0x89c36a63 [ 397.241546] Empty flash at 0x0707a814 ends at 0x0707b000 real 0m 2.15s user 0m 0.00s sys 0m 1.33s Starting init INIT: version 2.85 booting Mounting a tmpfs over /dev...done. Creating device nodes... and some more..done. /etc/init.d/minircS: 119: cannot create /sys/devices/platform/mmci-omap.2/enable_poll: Permission denied INIT: Entering runlevel: 2 Cleaning up /var/tmp Starting: fb-progress Starting DNS forwarder and DHCP server: dnsmasq. open(/dev/fb0): No such file or directory Starting system message bus: dbus. Starting Mode Controller Entity: mce. cat: /sys/devices/platform/omapfb/panel/name: No such file or directory cp: /etc/pointercal-.default: No such file or directory Error opening /dev/fb0: No such file or directory Fatal server error: no screens found DSME: process '/usr/bin/Xomap -mouse /dev/input/mouse0 -mouse /dev/input/event2 -dpi 96 ' with pid 609 exited with return value: 1 DSME: '/usr/bin/Xomap -mouse /dev/input/mouse0 -mouse /dev/input/event2 -dpi 96 ' exited with RESET policy -> reset Starting Periodical temporary file purging daemon Starting D-BUS session bus daemon Starting Sapwood image server Starting Matchbox window manager sapwood-server[645]: GLIB WARNING ** Gdk - cannot open display: (null) DSME: process '/usr/lib/sapwood/sapwood-server ' with pid 645 exited with return value: 1 DSME: '/usr/lib/sapwood/sapwood-server ' exited with RESET policy -> reset Received invalid message matchbox-wm: can't open display! check your DISPLAY variable. DSME: process '/usr/bin/matchbox-window-manager -theme default -use_titlebar yes -use_desktop_mode plain -use_lowlight no -use_cursor yes -use_dialog_mode static -use_super_modal yes' with pid 649 exited with return value: 1 DSME: '/usr/bin/matchbox-window-manager -theme default -use_titlebar yes -use_desktop_mode plain -use_lowlight no -use_cursor yes -use_dialog_mode static -use_super_modal yes' exited with RESET policy -> reset INIT: INIT: Sending processes the TERM signal INIT: Sending processes the KILL signal done. [ 473.278625] aic23 powering down [ 473.282806] Restarting system. [ 473.285949] .